Earlier daemon parameter was passed to
start_topology(), which is not needed now,
as new code is implemented to start
feature specific daemons.
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
OSPF when converging will choose a DR / Backup DR based upon
who has already come up. Irrelevant of priority. As such if
under system load OSPF comes up first and elects a DR that under
normal circumstances not be the elected one due to priority
OSPF does not go back through and re-elect to keep the system
stable in this case. Tests are experiencing this:
unet> r0 show ip ospf neigh
Neighbor ID Pri State Up Time Dead Time Address Interface RXmtL RqstL DBsmL
100.1.1.1 99 Full/Backup 4m14s 3.780s 10.0.1.2 r0-s1-eth0:10.0.1.1 0 0 0
100.1.1.2 0 Full/DROther 4m14s 3.848s 10.0.1.3 r0-s1-eth0:10.0.1.1 0 0 0
100.1.1.3 0 Full/DROther 4m14s 3.912s 10.0.1.4 r0-s1-eth0:10.0.1.1 0 0 0
unet> r1 show ip ospf neigh
Neighbor ID Pri State Up Time Dead Time Address Interface RXmtL RqstL DBsmL
100.1.1.0 98 Full/DR 4m15s 3.011s 10.0.1.1 r1-s1-eth1:10.0.1.2 0 0 0
100.1.1.2 0 Full/DROther 4m19s 3.124s 10.0.1.3 r1-s1-eth1:10.0.1.2 0 0 0
100.1.1.3 0 Full/DROther 4m19s 3.188s 10.0.1.4 r1-s1-eth1:10.0.1.2 0 0 0
unet> r2 show ip ospf neigh
Neighbor ID Pri State Up Time Dead Time Address Interface RXmtL RqstL DBsmL
100.1.1.0 98 Full/DR 4m27s 3.483s 10.0.1.1 r2-s1-eth0:10.0.1.3 0 0 0
100.1.1.1 99 Full/Backup 4m32s 3.527s 10.0.1.2 r2-s1-eth0:10.0.1.3 0 0 0
100.1.1.3 0 2-Way/DROther 4m32s 3.660s 10.0.1.4 r2-s1-eth0:10.0.1.3 0 0 0
unet> r3 show ip ospf neigh
Neighbor ID Pri State Up Time Dead Time Address Interface RXmtL RqstL DBsmL
100.1.1.0 98 Full/DR 4m55s 3.786s 10.0.1.1 r3-s1-eth1:10.0.1.4 0 0 0
100.1.1.1 99 Full/Backup 4m55s 3.829s 10.0.1.2 r3-s1-eth1:10.0.1.4 0 0 0
100.1.1.2 0 2-Way/DROther 4m54s 3.897s 10.0.1.3 r3-s1-eth1:10.0.1.4 0 0 0
Modify the test to do a clear to enforce the order we are specifically looking for.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The ospf_basic_functionality/test_ospf_lan.py creates
a ethernet segment and attaches 4 routers to it and
assigns ip addresses in a /24. As one of the tests
it picks a new address for r0 which coincides with
a ip address on r3. Then the test immediatly
checks for other data. The problem is of course
that if a test is `slow` enough hello's will
start to be ignored from r3 to r0 and the
neighbor relationships will come down. Choose
an ip address that doesn't cause this issue.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
1. Improved error meesage logging.
2. No functionality changes only put some meaningfull error messages.
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
1. Adding 18 ospf testcases to topojson.
2. Adding ospf.py library.
Test suite execution time is ~18 minutes.
Signed-off-by: naveen <nguggarigoud@vmware.com>
