Issue: (*,G) mroute uptime is not updated in mroute table,
after deleting and adding the RP
Root cause: When RP gets deleted or becomes not reachable, then
we un-install the entry from the kernel, but still maintains the
entry in the stack. When RP gets re-configured or becomes reachable,
"show ip mroute" shows the uptime, when the channel_oil gets created.
Fix: Introduce a new time mroute_creation in the channel_oil, gets
updated when mroute gets installed in the kernel.
Signed-off-by: Sarita Patra <saritap@vmware.com>
When FRR receives IGMP/PIM (*, G) join and RP is not configured or not
reachable, then we are creating a dummy upstream with incoming interface
as NULL and upstream address as INADDR_ANY.
Added upstream address and incoming interface validation where it is necessary,
before doing any operation on the upstream.
Signed-off-by: Sarita Patra <saritap@vmware.com>
Create a `struct pim_router` and move the thread master into it.
Future commits will further move global varaibles into the pim_router
structure.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When sending a sockoption for MRT_INIT, *bsd requires that
the data passed in must be 1. While linux does not, the
code was sending in a positive value that was causing issues
on *bsd of protocol not supported.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When trying to run PIM on *bsd, the kernel expects to only
allow the pim kernel socket to work if we elevate priviledges.
So do so.
This commit gets us further in the startup of PIM on *bsd
but is not sufficient to get it fully started yet.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Suppose we have a bridge with a host and two routers attached
to it.
r1 r2
| |
--------
|
host
host is sending traffic.
r1 and r2 are pim neighbors and r2 is the DR.
Both r1 and r2 will receive data from the stream up the pim
kernel socket. r1 will notice that it is not the DR and
stop processing in pim. This code adds a bit more code to blackhole
the route when r1 detects it is not the DR in this scenario.
This is being done because the kernel is both keeping state and
sending data to the pim process to continue processing this.
Additionally if we happen to be running this on a asic, then
blackholing the route in the asic can save a significant amount
of cpu time handling this situation.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The changes introduced in PR #1044 caused pim to notice
when a setsockopt call failed. The kicker here is that
this used to just work because we ignored the issue
pre. So VRF's need to BINDTODEVICE to get igmp callbacks
but the default vrf does not need to do so.
With the fix we now see IGMP group join:
root@dell-s6000-02 ~/frr# vtysh -c "show ip igmp group"
Interface Address Group Mode Timer Srcs V Uptime
br1 20.0.11.1 232.2.3.4 EXCL 00:04:14 1 3 00:00:05
Fixes: #1121
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
1) Error check return from setsockopt and sockets
2) Check return codes for str2prefix
3) Clean up some potential NULL References
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we receive a SGRPT Prune we were switching the upstream
to JOINED and immediately sending a join. This was not
the right thing to do.
This was happening because we were making decisions about the
new ifchannel before it was fully formed.
Rework ifchannel startup to provide enough information to
the pim upstream data structure to make the right decisions
Ticket: CM-16425
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Bind the pim kernel fd to the appropriate vrf, modify
the callback up into pim with the IGMP report to
retrieve the incoming interface and use that to
lookup the correct interface to use.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Move the upstream_list, hash and wheel into 'struct pim_instance'
Remove all pimg to pim in pim_upstream
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
As a transitory mechanism, if c_oil->pim is set, use that particular
pim instance, else use the default pimg.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we are handling the thread read/writes for
a pim mroute socket, make it so that it can
be appropriately handled by the 'struct pim_instance'
instead of defaulting to the default VRF's
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This change allows other non-linux platforms to be a bit
more forgiving if we ask for a very very large size.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Convert the socket fd to be owned by the pimg pointer as
well as the counters associated with the fd. This will
allow us to future proof our code.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we add a thread pointer to thread_add_XXX functions
when the specified function is called, thread.c is setting
the thread pointer to NULL. This was causing pim to
liberally pull it's zassert grenade pin's.
Additionally clean up code to not set the NULL pointer.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The FSF's address changed, and we had a mixture of comment styles for
the GPL file header. (The style with * at the beginning won out with
580 to 141 in existing files.)
Note: I've intentionally left intact other "variations" of the copyright
header, e.g. whether it says "Zebra", "Quagga", "FRR", or nothing.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
