Trivial conversion. As usual, combine multiple DEFUNs into a single
DEFPY for simplicity.
As a bonus of the northbound conversion, this commit fixes the
redistribution of certain protocols into ripd. The 'redist_type' array
used by the "redistribute" commands was terribly outdated, which was
preventing the CLI to parse correctly certain protocols like isis
and babel.
Remove the route_map hooks installed by rip_route_map_init() since they
were redundant (rip_init() already takes care of that).
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Trivial conversion.
'rip->default_information_route_map' was removed since it wasn't being
used anywhere.
'rip->default_information' was removed too because it was being used only
to display the running configuration and thus is not necessary anymore.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
The following types are nonstandard:
- u_char
- u_short
- u_int
- u_long
- u_int8_t
- u_int16_t
- u_int32_t
Replace them with the C99 standard types:
- uint8_t
- unsigned short
- unsigned int
- unsigned long
- uint8_t
- uint16_t
- uint32_t
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Allow the higher level protocol to specify if it would
like to receive notifications about it's routes that
it has installed.
I've purposely made it part of zclient_new_notify because
we need to track the routes on a per daemon basis only.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Allow rip_redistribute_add to receive and properly store
the nexthop type passed up from zebra.
Additionally display the different nexthop types appropriately.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
RIP is not using the nexthop data structure and as such when
it does not fully understand when it receives some of the
more exotic nexthop types what to do with it. This is the
start of a series of commits to allow RIP to start understanding
and properly displaying information about different nexthop
types.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This is a fallout from PR #1022 (zapi consolidation). In the early days,
the client daemons would allocate enough memory to send all nexthops
to zebra. Then zebra would add all nexthops to the RIB and respect
MULTIPATH_NUM only when installing the routes in the kernel. Now things
are different and the client daemons can send at most MULTIPATH_NUM
nexthops to zebra, and failure to respect that will result in a buffer
overflow. The MULTIPATH_NUM limit in the new zebra API is a small price
we pay to avoid allocating memory for each route sent to zebra.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Some differences compared to the old API:
* Now the redistributed routes are sent using address-family
independent messages (ZEBRA_REDISTRIBUTE_ROUTE_ADD and
ZEBRA_REDISTRIBUTE_ROUTE_DEL). This allows us to unify the ipv4/ipv6
zclient callbacks in the client daemons and thus remove a lot of
duplicate code;
* Now zebra sends all nexthops of the redistributed routes to the client
daemons, not only the first one. This shouldn't have any noticeable
performance implications and will allow us to remove an ugly exception
we had for ldpd (which needs to know all nexthops of the redistributed
routes). The other client daemons can simply ignore the nexthops if
they want or consult just the first one (e.g. ospfd/ospf6d/ripd/ripngd).
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This reverts commit c14777c6bf.
clang 5 is not widely available enough for people to indent with. This
is particularly problematic when rebasing/adjusting branches.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
This allows frr-reload.py (or anything else that scripts via vtysh)
to know if the vtysh command worked or hit an error.
The FSF's address changed, and we had a mixture of comment styles for
the GPL file header. (The style with * at the beginning won out with
580 to 141 in existing files.)
Note: I've intentionally left intact other "variations" of the copyright
header, e.g. whether it says "Zebra", "Quagga", "FRR", or nothing.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Somewhere in the past we switched from
using the auto-generated redistribute statements
to a non-generated version. This caused us to
loose new protocols to redistribute as they are
added. Put it back.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
All of the autogenerated macros in lib/route_types.pl are now called
FRR_* instead of QUAGGA_*.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This feature adds an L3 & L2 VPN application that makes use of the VPN
and Encap SAFIs. This code is currently used to support IETF NVO3 style
operation. In NVO3 terminology it provides the Network Virtualization
Authority (NVA) and the ability to import/export IP prefixes and MAC
addresses from Network Virtualization Edges (NVEs). The code supports
per-NVE tables.
The NVE-NVA protocol used to communicate routing and Ethernet / Layer 2
(L2) forwarding information between NVAs and NVEs is referred to as the
Remote Forwarder Protocol (RFP). OpenFlow is an example RFP. For
general background on NVO3 and RFP concepts see [1]. For information on
Openflow see [2].
RFPs are integrated with BGP via the RF API contained in the new "rfapi"
BGP sub-directory. Currently, only a simple example RFP is included in
Quagga. Developers may use this example as a starting point to integrate
Quagga with an RFP of their choosing, e.g., OpenFlow. The RFAPI code
also supports the ability import/export of routing information between
VNC and customer edge routers (CEs) operating within a virtual
network. Import/export may take place between BGP views or to the
default zebera VRF.
BGP, with IP VPNs and Tunnel Encapsulation, is used to distribute VPN
information between NVAs. BGP based IP VPN support is defined in
RFC4364, BGP/MPLS IP Virtual Private Networks (VPNs), and RFC4659,
BGP-MPLS IP Virtual Private Network (VPN) Extension for IPv6 VPN . Use
of both the Encapsulation Subsequent Address Family Identifier (SAFI)
and the Tunnel Encapsulation Attribute, RFC5512, The BGP Encapsulation
Subsequent Address Family Identifier (SAFI) and the BGP Tunnel
Encapsulation Attribute, are supported. MAC address distribution does
not follow any standard BGB encoding, although it was inspired by the
early IETF EVPN concepts.
The feature is conditionally compiled and disabled by default.
Use the --enable-bgp-vnc configure option to enable.
The majority of this code was authored by G. Paul Ziemba
<paulz@labn.net>.
[1] http://tools.ietf.org/html/draft-ietf-nvo3-nve-nva-cp-req
[2] https://www.opennetworking.org/sdn-resources/technical-library
Now includes changes needed to merge with cmaster-next.
* zclient.c: prefix length on router-id and interface address add
messages not sanity checked. fix.
* */*_zebra.c: Prefix length on zebra route read was not checked, and
clients use it to write to storage. An evil zebra could overflow
client structures by sending overly long prefixlen.
Prompted by discussions with:
Donald Sharp <sharpd@cumulusnetworks.com>
Since recently zebra uses only the ZEBRA_REDISTRIBUTE_* messages
to advertise redistributed routes to its clientes. Now the old
ZEBRA_IPV*_ROUTE_* messages are only used for client->zebra communication.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Introduce a new command "[no] allow-ecmp" to enable/disable the
ECMP feature in RIP. By default, ECMP is not allowed.
Once ECMP is disabled, only one route entry can exist in the list.
* rip_zebra.c: adjust a debugging information, which shows the number
of nexthops according to whether ECMP is enabled.
* ripd.c: rip_ecmp_add() will reject the new route if ECMP is not
allowed and some entry already exists.
A new configurable command "allow-ecmp" is added to control
whether ECMP is allowed.
When ECMP is disabled, rip_ecmp_disable() is called to
remove the multiple nexthops.
* ripd.h: Add a new member "ecmp" to "struct rip", indicating whether
ECMP is allowed or not.
Signed-off-by: Feng Lu <lu.feng@6wind.com>
Reviewed-by: Alain Ritoux <alain.ritoux@6wind.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
(cherry picked from commit 0b74a0a5db7bcf65bf68c44b547b02b1310b5cdb)
* Each node in the routing table is changed into a list, holding
the multiple equal-cost paths.
* If one of the multiple entries gets less-preferred (greater
metric or greater distance), it will be directly deleted instead
of starting a garbage-collection timer for it.
The garbage-collection timer is started only when the last entry
in the list gets INFINITY.
* Some new functions are used to maintain the ECMP list. And hence
rip_rte_process(), rip_redistribute_add() and rip_timeout() are
significantly simplified.
* rip_zebra_ipv4_add() and rip_zebra_ipv4_delete() now can share
the common code. The common part is moved to rip_zebra_ipv4_send().
Signed-off-by: Feng Lu <lu.feng@6wind.com>
Reviewed-by: Alain Ritoux <alain.ritoux@6wind.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
(cherry picked from commit b397cf4f0fc484c5ebfc8a680090055c8e6cbe32)
Conflicts:
ripd/rip_zebra.c
Clients (BGP, OSPF etc.) register with Zebra for information about
a VRF such as Router ID, interfaces and redistribution. Add API to
support unregister also which is required for the non-default VRF.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-9128
Reviewed By: CCR-4098
Testing Done: Manual testing
When rip is not configured and zebra decides to send
a default route to it, check to make sure that rip is
configured before accepting anything from zebra.
Ticket: CM-9270
Reviewed-by: Don Slice
Tested: OSPF test case that was erroring out no longer
happens
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
