When trying to track down a MTYPE_TMP memory leak
it's harder to search for it when you happen to
have some usage of ttable_dump. Let's just give
it it's own memory type so that we can avoid
confusion in the future.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Currently the FRR code will receive both kernel and
connected routes that do not actually have an underlying
nexthop group at all. Zebra turns around and creates
a `matching` nexthop hash entry and installs it.
For connected routes, this will create 2 singleton
nexthops in the dplane per interface (v4 and v6).
For kernel routes it would just create 1 singleton
nexthop that might be used or not.
This is bad because the dplane has a limited amount
of space available for nexthop entries and if you
happen to have a large number of interfaces then
all of a sudden you have 2x(# of interfaces) singleton
nexthops.
Let's modify the code to delay creation of these singleton
nexthops until they have been used by something else in the
system.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Let's display the afi of the nexthop hash entry. Right
now it is impossible to tell the difference between v4 or
v6 nexthops, especially since it is important for the kernel.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Move the prefix lookup/comparison to outside the re loop
and into the rn loop, since that is where the code should
actually be.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Current code when a link is set down is to just mark the
nexthop group as not properly setup. Leaving situations
where when an interface goes down and show output is
entered we see incorrect state. This is true for anything
that would be checking those flags at that point in time.
Modify the interface down nexthop group code to notice the
nexthops appropriately ( and I mean set the appropriate flags )
and to allow a `show ip route` command to actually display
what is going on with the nexthops.
eva# show ip route 1.0.0.0
Routing entry for 1.0.0.0/32
Known via "sharp", distance 150, metric 0, best
Last update 00:00:06 ago
* 192.168.44.33, via dummy1, weight 1
* 192.168.45.33, via dummy2, weight 1
sharpd@eva:~/frr1$ sudo ip link set dummy2 down
eva# show ip route 1.0.0.0
Routing entry for 1.0.0.0/32
Known via "sharp", distance 150, metric 0, best
Last update 00:00:12 ago
* 192.168.44.33, via dummy1, weight 1
192.168.45.33, via dummy2 inactive, weight 1
Notice now that the 1.0.0.0/32 route now correctly
displays the route for the nexthop group entry.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Add a new start option "-K" to libfrr to denote a graceful start,
and use it in zebra and bgpd.
zebra will use this option to denote a planned FRR graceful restart
(supporting only bgpd currently) to wait for a route sync completion
from bgpd before cleaning up old stale routes from the FIB. An optional
timer provides an upper-bounds for this cleanup.
bgpd will use this option to denote either a planned FRR graceful
restart or a bgpd-only graceful restart, and this will drive the BGP
GR restarting router procedures.
Signed-off-by: Vivek Venkatraman <vivek@nvidia.com>
When displaying a route table in JSON, a table JSON object is storing
all the prefix JSON objects containing the prefix information. This
results in excessive memory allocation for JSON objects, potentially
leading to an out-of-memory error on the machine with large routing
tables.
To Fix the memory consumption issue for the "show ip[v6] route [vrf XX]
json" command, display the prefixes one by one and free the memory of
each JSON object after it has been displayed.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
0e2fc3d67f ("vtysh, zebra: Fix malformed json output for multiple vrfs
in command 'show ip route vrf all json'") has been reverted in the
previous commit. Although the fix was correct, it was consuming too muca
memory when displaying large route tables.
A root JSON object was storing all the JSON objects containing the route
tables, each containing their respective prefixes in JSON objects. This
resulted in excessive memory allocation for JSON objects, potentially
leading to an out-of-memory error on the machine.
To Fix the memory consumption issue for the "show ip[v6] route vrf all
json" command, display the tables one by one and free the memory of each
JSON object after it has been displayed.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
This reverts commit 0e2fc3d67f.
This fix was correct but not optimal for memory consumption at scale.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Include the prefix source address when set by a route-map in
show output for routes, in various formats.
Add some debugs when encoding netlink route messages with
a source address.
Signed-off-by: Mark Stapp <mjs@cisco.com>
Change input/output arguments of the RPC callback from lists of
(xpath/value) tuples to YANG data trees.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Command 'show ip route vrf <vrf_name> json' returns a valid json object,
however if instead of <vrf_name> we specify 'all', we get an invalid json
object, like:
{//vrf1 routes}{//vrf2 routes}{vrf3 routes}
After the fix:
{"vrf1":{//vrf1 routes},"vrf2:{//vrf2 routes},"vrf3":{//vrf3 routes}}
Which is a valid json object, that can be parsed effectively using built-in
modules. The rest of the commands remains unaffected and behave the same.
Signed-off-by: Piotr Suchy <psuchy@akamai.com>
The current code is unsetting the fact that the
NHG is installed. It is installed but we are
reinstalling it. Let's note this in the code
appropriately as REINSTALL and not remove the
INSTALLED FLAG.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
- unnecessary command duplication
- usage of oper data during validation
- unnecessary checks for things that can't happen
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
The nexthop group route replace operation was made consistent
across all versions of the kernel. A v6 route replacement
does not need to do a delete than add when using nexthop
groups
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The v6_rr_semantics variable was being set but never
reported and had to be inferred from watching netlink
messages to the kernel. Let's add a bit of code
to `show zebra` so that we can know how it is being
used.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Create Local routes in FRR:
S 0.0.0.0/0 [1/0] via 192.168.119.1, enp39s0, weight 1, 00:03:46
K>* 0.0.0.0/0 [0/100] via 192.168.119.1, enp39s0, 00:03:51
O 192.168.119.0/24 [110/100] is directly connected, enp39s0, weight 1, 00:03:46
C>* 192.168.119.0/24 is directly connected, enp39s0, 00:03:51
L>* 192.168.119.224/32 is directly connected, enp39s0, 00:03:51
O 192.168.119.229/32 [110/100] via 0.0.0.0, enp39s0 inactive, weight 1, 00:03:46
C>* 192.168.119.229/32 is directly connected, enp39s0, 00:03:46
Create ability to redistribute local routes.
Modify tests to support this change.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Currently, json output of show ip route command are no pretty format.
This is an extremely expensive operation at high scale
(with high number of routes with many paths).
Zebra json non-pretty command support added:
```
show ip route json
```
Ticket:#3513256
Issue:3513256
Testing: UT done
Signed-off-by: Sindhu Parvathi Gopinathan's <sgopinathan@nvidia.com>
The default vrf is generally non-NULL, except when shutdown. So, most
of the time it is not necessary to check if it is NULL, we should
remove the useless checks for it.
Searched them with exact match:
```
grep -rI "zebra_vrf_lookup_by_id(VRF_DEFAULT)" | wc -l
31
```
Signed-off-by: anlan_cs <vic.lan@pica8.com>
a) Consolidate v4 and v6 versions of rib_match_multicast
b) Improve debug to show what we matched against as well.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The `show evpn next-hop svd *` command doesn't provide much
for users right now. Make it hidden so we can still debug
the tables with it.
Also remove SVD output from `show evpn next-hop vni all`.
Signed-off-by: Stephen Worley <sworley@nvidia.com>
Add some show commands and expand some already existing
commands so we can get debug info from the SVD global
neigh table inside zebra.
Signed-off-by: Stephen Worley <sworley@nvidia.com>
Use the already existing mpls label code to store VNI
info for vxlan. VNI's are defined as labels just like mpls,
we should be using the same code for both.
This patch is the first part of that. Next we will need to
abstract the label code to not be so mpls specific. Currently
in this, we are just treating VXLAN as a label type and storing
it that way.
Signed-off-by: Stephen Worley <sworley@nvidia.com>
This patch addresses following bug fixes
- Fix vtysh doc string in "show evpn access-vlan..." command
- Multicast group handling was little complex. This change avoids calling
multiple functions and directly calls the zebra_vxlan_if_update_vni for
mcast group updates.
- When a vlan-vni map is removed, the removed vni deletion was happening
in FRR with SVD config. This was resulting in stale vni and not
resulting propagation of the vni deletion.
During vni cleanup (zebra_vxlan_if_vni_clean) zebra_vxlan_if_vni_del
was called for vni delete which is not correct. We should be calling
zebra_vxlan_if_vni_entry_del for the given vni entry.
Signed-off-by: Sharath Ramamurthy <sramamurthy@nvidia.com>
Multiple vlan aware bridge data structure changes and its corresponding bridge
handling changes.
A new vlan-table is maintained for each bridge which records the zebra_l2_bridge_vlan
entry. zebra_l2_bridge_vlan maps vlan to access_bd associated to this bridge.
Existing zebra_evpn_access_bd structure is vlan aware which is now modified to be
(vlan, bridge) aware.
Whenever a new access_bd is instantiated, a corresponding entry is also recorded
in the zebra l2 bridge for the vlan.
When the access_bd is dereferenced or whenever a bridge is deleted, the
association is cleaned up.
Signed-off-by: Sharath Ramamurthy <sramamurthy@nvidia.com>
Add affinity-map hooks to check the utilization of affinity-map in
link-params before its deletion and to update link-params when the
affinity-map bit-position is updated.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Add the affinity-map global command to zebra. The syntax is:
> affinity-map NAME bit-position (0-1023)
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
1. Renamed "gates" to "nexthops"
2. Displaying afi of the nexthops being dispalyed in place of
"nexthops" JSON object in the old JSON output
3. Calling show_route_nexthop_helper() and show_nexthop_json_helper()
instead of print_nh() inorder to keeps the fields in "nexthops"
JSON object in sync with "nexthops" JSON object of
"show nexthop-group rib json".
Updated vtysh:
r1# show ip nht
192.168.0.2
resolved via connected
is directly connected, r1-eth0 (vrf default)
Client list: static(fd 28)
192.168.0.4
resolved via connected
is directly connected, r1-eth0 (vrf default)
Client list: static(fd 28)
Updated JSON:
r1# show ip nht json
{
"default":{
"ipv4":{
"192.168.0.2":{
"nhtConnected":false,
"clientList":[
{
"protocol":"static",
"socket":28,
"protocolFiltered":"none"
}
],
"nexthops":[
{
"flags":3,
"fib":true,
"directlyConnected":true,
"interfaceIndex":2,
"interfaceName":"r1-eth0",
"vrf":"default",
"active":true
}
],
"resolvedProtocol":"connected"
}
}
}
}
Signed-off-by: Pooja Jagadeesh Doijode <pdoijode@nvidia.com>
