(Somewhat) useful when dealing with an interface that has only one host
attached. Only works for IGMPv2 and MLDv1, other protocol versions have
no leave message.
Co-authored-by: David Lamparter <equinox@opensourcerouting.org>
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
For groups we can just look at the length of the list, for sources we
need to count them on a per-interface level.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Add options for group-list and source-list, both of which take a prefix list name.
The prefix list is used to determine the lookup mode for specific sources and/or groups.
Any number of lookup modes can be configured as long as the combination of group
and source list is unique.
A global lookup mode (empty group and source lists) is always added and defaults to mrib-then-urib
as it currently functions. The global lookup mode can be changed as it current exists with the command
`rpf-lookup-mode MODE`.
When determinig which mode to use, match source (and group if provided) against the lists, if they are set.
If a lookup does not specify a group, then only use lookup modes that do not have a group list defined.
A lookup by definition will have a source, so no special handling there.
Signed-off-by: Nathan Bahr <nbahr@atcorp.com>
Add rpf-lookup-mode MODE vty command under router pim block.
Including NB piping and config write. Using the mode still pending.
Signed-off-by: Nathan Bahr <nbahr@atcorp.com>
Add new interface command ip multicast boundary ACCESSLIST4_NAME. This
allows filtering on both source and group using the extended access-list
syntax vs. group-only as with the existing "ip multicast boundary oil"
command, which uses prefix-lists. If both are configured, the prefix-
list is evaluated first. The default behavior for both prefix-lists and
access-lists remains "deny", so the prefix-list must have a terminating
"permit" statement in order to also evaluate against the access-list.
The following example denies groups in range 229.1.1.0/24 and groups in
range 232.1.1.0/24 with source 10.0.20.2:
!
ip prefix-list pim-oil-plist seq 10 deny 229.1.1.0/24
ip prefix-list pim-oil-plist seq 20 permit any
!
access-list pim-acl seq 10 deny ip host 10.0.20.2 232.1.1.0 0.0.0.255
access-list pim-acl seq 20 permit ip any any
!
interface r1-eth0
ip address 10.0.20.1/24
ip igmp
ip pim
ip multicast boundary oil pim-oil-plist
ip multicast boundary pim-acl
!
Signed-off-by: Corey Siltala <csiltala@atcorp.com>
Add MSDP shutdown and SA limiting configuration to YANG model.
(no implementation, just boiler plate code)
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Implement embedded RP support and configuration commands.
Embedded RP is disabled by default and can be globally enabled with the
command `embedded-rp` in the PIMv6 configuration node.
It supports the following options:
- Embedded RP maximum limit
- Embedded RP group filtering
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
New CLI commands added:
router pim [vrf NAME]
autorp discovery
autorp announce RP-ADDR [GROUP | group-list PREFIX-LIST]
autorp announce {scope (1-255) | interval (1-65535) | holdtime (0-65535)}
autorp discovery
Enables Auto RP discovery for learning dynamic RP information using the
AutoRP protocol.
autorp announce RP-ADDR [GROUP | group-list PREFIX-LIST]
Enable announcements of a candidate RP with the given group range, or
prefix list of group ranges, to an AutoRP mapping agent.
autorp announce {scope (1-255) | interval (1-65535) | holdtime (0-65535)}
Configure the parameters of the AutoRP announcement messages.
The scope sets the packet TTL.
The interval sets the time between TX of announcements.
The holdtime sets the hold time in the message, the time the mapping
agent should wait before invalidating the candidate RP information.
debug pim autorp
Enable debug logging of the AutoRP protocol
show ip pim [vrf NAME] autorp [json]
Show details of the AutoRP protocol.
To view learned RP info, use the existing command 'show ip pim rp-info'
Extend pim yang for new configuration:
augment /frr-rt:routing/frr-rt:control-plane-protocols/frr-rt:control-plane-protocol/frr-pim:pim/frr-pim:address-family:
+--rw rp
+--rw auto-rp
+--rw discovery-enabled? boolean
+--rw announce-scope? uint8
+--rw announce-interval? uint16
+--rw announce-holdtime? uint16
+--rw candidate-rp-list* [rp-address]
+--rw rp-address inet:ip-address
+--rw (group-or-prefix-list)?
+--:(group)
| +--rw group? frr-route-types:ip-multicast-group-prefix
+--:(prefix-list)
+--rw prefix-list? plist-ref
Signed-off-by: Nathan Bahr <nbahr@atcorp.com>
This will add a static IGMP group that does not rely on an underlying
socket join which sends traffic to the cpu unneccesarily. Instead, the
groups are joined directly without any IGMP interactions.
New command is under interfaces, 'ip igmp static-group ...'.
Added an alias for 'ip igmp join ...' to 'ip igmp join-group'.
Moved IGMP join groups to new yang list "join-group" and reused
the "static-group" list for the IGMP static groups.
Signed-off-by: Nathan Bahr <nbahr@atcorp.com>
Implement MSDP MD5 authentication connection support.
Implementation details:
- Move the MSDP socket creation code to a generic function so it can be
parametrized to be used with/without authentication.
- The MSDP peer connection will not change when the configuration is
set, instead it will only be applied next connection or when
`clear ip msdp peer A.B.C.D` is called.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Implement MSDP peer incoming/outgoing SA filter.
Note
----
Cisco extended access list has a special meaning: the first address is
the source address to filter.
Example:
! The rules below filter some LAN prefix to be leaked out
access-list filter-lan-source deny ip 192.168.0.0 0.0.255.255 224.0.0.0 0.255.255.255
access-list filter-lan-source permit any
router pim
msdp peer 192.168.0.1 sa-filter filter-lan-source out
! The rules below filter some special management group from being
! learned
access-list filter-management-group deny 230.0.0.0 0.255.255.255
access-list filter-management-group permit any
router pim
msdp peer 192.168.0.1 sa-filter filter-management-group in
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Renamed frr-igmp.yang to frr-gmp.yang, igmp to gmp container.
to support IGMP and MLD protocol.
frr-gmp.yang, created a list of address family under mgmd
container. For PIMV4 the key is IPV4, where as for PIMV6
the key is IPV6. This is done for PIMV6 development.
This commit will have all the northbound changes to support
IPV4 address family.
Signed-off-by: sarita patra <saritap@vmware.com>
frr-pim.yang, created a list of address family under pim
container. For PIMV4 the key is IPV4, where as for PIMV6
the key is IPV6. This is done for PIMV6 development.
This commit will have all the northbound changes to support
IPV4 address family.
Signed-off-by: sarita patra <saritap@vmware.com>
Fully utilize the northbound to hold pointers to our private data
instead of searching for data structures every time we need to change a
configuration.
Highlights:
* Support multiple mesh groups per PIM instance (instead of one)
* Use DEFPY instead of DEFUN to reduce code complexity
* Use northbound private pointers to store data structures
* Reduce callback names size
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
