When we uplifted the cli from old -> new, I did not properly
handle the switch from <1-3> to (1-3) for number ranges.
Also fix some minor variable renaming that happened?
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This was causing a crash when no group address was passed
because a garbage pointer valuse was used. It also was ignoring
the group address when passing one.
Signed-off-by: Jafar Al-Gharaibeh <jafar@atcorp.com>
Execute ip igmp version 3 under swp interface,
verified show running displayed 'ip igmp' configuration.
Continuous sending group membership, performed 'no ip igmp'
and verified, group membership flushed. Performed
'ip igmp version 3', verified 'show ip igmp groups'
displaying igmp membership re-populated.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
In this patch, PIM nexthop tracking uses locally populated nexthop cached list
to determine ECMP based nexthop (w/ ECMP knob enabled), otherwise picks
the first nexthop as RPF.
Introduced '[no] ip pim ecmp' command to enable/disable PIM ECMP knob.
By default, PIM ECMP is disabled.
Intorudced '[no] ip pim ecmp rebalance' command to provide existing mcache
entry to switch new path based on hash chosen path.
Introduced, show command to display pim registered addresses and respective nexthops.
Introuduce, show command to find nexthop and out interface for (S,G) or (RP,G).
Re-Register an address with nexthop when Interface UP event received,
to ensure the PIM nexthop cache is updated (being PIM enabled).
During PIM neighbor UP, traverse all RPs and Upstreams nexthop and determine, if
any of nexthop's IPv4 address changes/resolves due to neigbor UP event.
Testing Done: Run various LHR, RP and FHR related cases to resolve RPF using
nexthop cache with ECMP knob disabled, performed interface/PIM neighbor flap events.
Executed pim-smoke with knob disabled.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
(cherry picked from commit cba4448178)
To the 'ip pim spt-switchover infinity-and-beyond' command
add 'prefix-list <PLIST>'. To the command.
Use this as the basis to deny (Not immediate switchover)
or permit (Immediate switchover), based upon matching
the group address and the prefix-list.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Interface type has been replaced with the SSM range config. And SSM
groups can now co-exists with ASM groups. I have left the pim ssm
per-interface cli control hidden. It now enables pim-sm with a warning.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-15344
Testing Done: pim-smoke
SSM groups (232/8 or user configured SSM range) can exist in the same
multicast network as ASM groups. For such groups all RPT related state
machine operations have to be skipped as defined by section 4.8 of
RFC4601 -
1. Source registration is skipped for SSM groups. For SSM groups mroute
is setup on the FHR when a new multicast flow is rxed; however source
registration (i.e. pimreg join) is skipped. This will let the ASIC black
hole the traffic till a valid OIL is added to the mroute.
2. (*,G) IGMP registrations are ignored for SSM groups.
Sample output:
=============
fhr# sh ip pim group-type
SSM group range : 232.0.0.0/8
fhr# sh ip pim group-type 232.1.1.1
Group type: SSM
fhr# sh ip pim group-type 239.1.1.1
Group type: ASM
fhr#
Sample config:
=============
fhr(config)# ip pim ssm prefix-list ssm-ranges
fhr(config)#
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-15344
Testing Done:
1. SSM/ASM source-registration/igmp-joins.
2. On the fly multicast group type changes.
3. pim-smoke.
When we get a SGrpt Prune embedded in the *,G Join,
Display the created ifchannel as being SGRpt state.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Changed the state field in the "sh ip pim upstream" output to include
register and join state info as a comma separated value. Register info
is supressed if reg-state=NoInfo.
Sample output:
=============
root@fhr:/home/cumulus# net show pim upstream
Iif Source Group State Uptime JoinTimer
RSTimer KATimer RefCnt
swp1 33.1.1.1 239.1.1.2 J,RegP 00:00:18 --:--:--
00:00:44 00:03:24 2
root@fhr:/home/cumulus#
root@rp:/home/cumulus# net show pim upstream
Iif Source Group State Uptime JoinTimer
RSTimer KATimer RefCnt
lo * 239.1.1.2 J 00:02:08 00:00:52
--:--:-- --:--:-- 1
swp1 33.1.1.1 239.1.1.2 J 00:00:16 00:00:11
--:--:-- 00:03:26 1
root@rp:/home/cumulus#
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-14700
Testing Done: pim-smoke
With the separation of register-state and upstream-join-state we no
longer need an enumeration that covers both states. This commit includes
the following -
1. Defined new enumeration for reg state (this 1:1 with RFC4601).
2. Dropped JOIN_PENDING enum value from upstream join state. RFC4601
only define two values NOT_JOINED and JOINED for this state.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-14700
Testing Done: Verified register setup manually and ran pim-smoke
On the FHR upstream-join-state is not particularly relevant as we
don't need to send upstream JPs for the SG. So that field was being
overloaded with the register-state. However some of the events that
triggered changes to the JoinDesired macro were accidentally overwriting
the state with join info (instead of treating it as register info)
confusing the register state machine.
To make the PIM RFC macros' implemention simple I have separated out
the register-state. And upstream->state now solely describes the
upstream-join-state independent of the role of the PIM router.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-14700
Testing Done: verified pim-register state-machine with separate and
combined FHR/RP routers. Also ran pim-smoke.
The 'show ip pim state' command was not
working quite correctly from when
we moved over to the new vtysh-grammar.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Automatically turn on pim if the daemon is turned on.
Hide the 'ip multicast-routing' command
Disable the 'no ip multicast-routing' command
Do not display the 'ip multicast-routing' command.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When you enter these commands, under an interface:
ip igmp version ...
ip igmp query-interval ...
ip igmp query-max-response-time ...
ip igmp query-max-response-time-dsec ...
These commands will now just turn on igmp for the
interface.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add the ability for PIM to send Join/Prunes as an
aggregated message instead of individual messages
for each S,G.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Cleanup the in_ifname and out_ifname buffers
to be large enough to hold the actual interface
names.
Additionally move the common variables to be defined
once, instead of inside of multiple for loops
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
PIM was handling vif creation deletion poorly
for interface down and up events. Fix this
issue by keeping track of which vif index'es
we have issued and allow the wholes to be
filled in.
Ticket: CM-14556
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This commit does these three things:
1) Add code to 'show ip pim state' to show where OIF's got their
decision to include that interface
2) Add code in pim_mroute_[add|del] to display what we think we are
adding to the kernel
3) Add code to properly track where we got the incoming request from and
to appropriately not remove a OIL if we have state still
Ticket: CM-14034
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Chirag Shah <chirag@cumulusnetworks.com>
Start the abstraction of the zclient data structure out from a
global variable for the entire program to a global variable
to the pim_zebra.c file.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
We were adding the 'ip msdp ...' command to
the parser 2x. Some new code added to the
parser apparently catches this for us now.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Mixing well-known and variable property names makes the output difficult
to parse. so wrapped variable-keyed dicts with well-known property
names (such as "oil") in the following outputs -
"show ip mroute json"
"show ip msdp mesh-group json"
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
There exists situations where we have noted that
we need to rescan but have missed the window
of opportunity to actually redo the scan
so for the moment allow the S,G 30 second
scanner notice the missed opportunity and
fix it. We'll remove this later.
Ticket: CM-13988
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Modify pim_usptream_new to auto create the pim
channel oil. Why? Because there exists situations
where we have upstream state and we are attempting
to set the inherited_olist on it and we have
not created the channel oil yet. When that
happens we end up with mroutes that are
being meanies.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When debugging is turned on for 'debug mroute' we
are unable to tell when a mroute has been added
or deleted from the mrib. Notice when we
do it and who called it.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Make the 'ip igmp query-max-response-time' command
take input in deci-seconds and make the
'ip igmp query-max-response-time-dsec' command hidden.
Ticket:CM-13786
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Was failing with a vague error -
"Source set failed"
Changed to used the error string (used by the rest of the commands) -
"Pim not enabled on this interface"
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Anycast rp requires multiple ip addresses on the lo. If PIM is used in
an unnumbered BGP network it picks one of the lo addresses as the
pim-primary for the swp interfaces. But if the anycast IP is picked up
by both sides pim nbr will never converge. So a static "use-source" config
is provided to allow the administrator to force the the hello source to the
unique IP address.
Sample output:
=============
dell-s6000-04(config-if)# do show running-config pimd
>>>>>> SNIPPED >>>>>>>>>>>>>>>>>
interface lo
ip pim sm
ip pim use-source 100.1.1.5
!
>>>>>> SNIPPED >>>>>>>>>>>>>>>>>
dell-s6000-04(config-if)# do show ip pim interface lo
Interface : lo
State : up
Use Source : 100.1.1.5
Address : 100.1.1.5 (primary)
100.1.1.100
>>>>>> SNIPPED >>>>>>>>>>>>>>>>>
dell-s6000-04(config-if)# do show ip pim interface lo json
{
"lo":{
"name":"lo",
"state":"up",
"address":"100.1.1.5",
"index":1,
"lanDelayEnabled":true,
"useSource":"100.1.1.5",
"secondaryAddressList":[
"100.1.1.100"
],
>>>>>> SNIPPED >>>>>>>>>>>>>>>>>
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
