Support filtering extended communities with a callback. So that we can
strip multiple values in one pass.
Signed-off-by: Xiao Liang <shaw.leon@gmail.com>
The exact-match and the any options are missing for the extended
communities. Add missing options that are present on the match
operations for communities and large-communities.
> route-map rmap permit 1
> match extcommunity 1
> exit
> !
> route-map rmap permit 2
> match extcommunity 2 any
> exit
> !
> route-map rmap permit 3
> match extcommunity 3 exact-match
> exit
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The L2 attribute extended community can not be decoded when using L2VPN
EVPN as a route reflector. Decode the extended community and dump the
detailed information about flags and MTU information.
> rt4# show bgp l2vpn evpn
> BGP table version is 1, local router ID is 4.4.4.4
> Status codes: s suppressed, d damped, h history, * valid, > best, i - internal
> Origin codes: i - IGP, e - EGP, ? - incomplete
> EVPN type-1 prefix: [1]:[EthTag]:[ESI]:[IPlen]:[VTEP-IP]:[Frag-id]
> EVPN type-2 prefix: [2]:[EthTag]:[MAClen]:[MAC]:[IPlen]:[IP]
> EVPN type-3 prefix: [3]:[EthTag]:[IPlen]:[OrigIP]
> EVPN type-4 prefix: [4]:[ESI]:[IPlen]:[OrigIP]
> EVPN type-5 prefix: [5]:[EthTag]:[IPlen]:[IP]
>
> Network Next Hop Metric LocPrf Weight Path
> Route Distinguisher: 1.1.1.1:100
> *>i[1]:[12]:[00:00:00:00:00:00:00:00:00:00]:[32]:[0.0.0.0]:[0]
> 1.1.1.1 100 0 i
> RT:65500:100 L2: P flag:N, B Flag N, C word N, MTU 0
> Route Distinguisher: 5.5.5.5:100
> *>i[1]:[10]:[00:00:00:00:00:00:00:00:00:00]:[32]:[0.0.0.0]:[0]
> 5.5.5.5 100 0 i
> RT:65500:100 L2: P flag:N, B Flag N, C word N, MTU 0
>
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The type of the val field in ecommunity_val is used inconsistently
in a number of places. It should be defined as uint8_t.
Signed-off-by: Enke Chen <enchen@paloaltonetworks.com>
Link-bandwidth is encoded into extended community, not ipv6 extended community.
Thus it's not needed here at all.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
This is needed to implement and use larger bandwidths rather than limiting only
to theoretical 34Gbps max bandwidth.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
When exporting BGP prefixes, it is necessary to configure
the route target extended communities with the following
command:
> rt vpn export <RouteTarget>
But the customer may need to configure the route-target to
apply to bgp updates, solely based on a route-map criterium.
by using the below route-map configured like that:
> route-map vpn export <routemapname>
Fix this by allowing to export bgp updates based on the
presence of route-targets on either route-map or vpn
configured rt. the exportation process is stopped
if no route target is available in the ecommunity list.
Fixes: ddb5b4880b ("bgpd: vpn-vrf route leaking")
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
add support of color extended community, conforming to RFC 9012.
This extended community will be added to the existing one, RT,SOO
and Node Target. The configuration will be made through the
route-map service.
find above a configuration example:
router bgp 65001
bgp router-id 192.168.1.1
no bgp ebgp-requires-policy
no bgp network import-check
neighbor 192.168.1.2 remote-as external
neighbor 192.168.1.3 remote-as external
neighbor 192.168.1.4 remote-as external
address-family ipv4 unicast
network 10.10.10.10/24 route-map rmap
exit-address-family
!
route-map rmap permit 10
set extcommunity color 55555 200
exit
Signed-off-by: Francois Dumontet <francois.dumontet@6wind.com>
Initial support for configuring an SoO for all MAC-VRFs (EVIs/L2VNIs).
This provides a topology-independent method of preventing EVPN routes
from one MAC-VRF "site" (an L2 domain) from being imported by other PEs
in the same MAC-VRF "site", similar to how SoO is traditionally used in
L3VPN to identify and break loops for an L3/IP-VRF "site".
One example of where a MAC-VRF SoO can be used to avoid an L2 control
plane loop is with Active/Active MLAG VTEPs. For a given L2 site only
one control plane should be active. SoO can be used to ID/ignore entries
originated from the local MAC-VRF site so that EVPN will not attempt to
manage entries that are already handled by MLAG.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
Before this patch, this function wasn't used in the code. Let's reuse this
since it's uses the same pattern for encoding route-target extcommunity.
Also reuse encode_route_target_as[4]() as well.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
kttps://datatracker.ietf.org/doc/html/draft-ietf-idr-node-target-ext-comm
unet> sh r1 vtysh -c 'sh ip bgp nei 192.168.1.2 adver'
BGP table version is 1, local router ID is 192.168.1.1, vrf id 0
Default local pref 100, local AS 65001
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found
Network Next Hop Metric LocPrf Weight Path
*> 10.10.10.10/32 0.0.0.0 0 32768 i
Total number of prefixes 1
unet> sh r1 vtysh -c 'sh ip bgp nei 192.168.1.3 adver'
BGP table version is 1, local router ID is 192.168.1.1, vrf id 0
Default local pref 100, local AS 65001
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found
Network Next Hop Metric LocPrf Weight Path
*> 10.10.10.10/32 0.0.0.0 0 32768 i
Total number of prefixes 1
unet> sh r2 vtysh -c 'show ip bgp 10.10.10.10/32'
% Network not in table
unet> sh r3 vtysh -c 'show ip bgp 10.10.10.10/32'
BGP routing table entry for 10.10.10.10/32, version 1
Paths: (1 available, best #1, table default)
Advertised to non peer-group peers:
192.168.1.1
65001
192.168.1.1 from 192.168.1.1 (192.168.1.1)
Origin IGP, metric 0, valid, external, best (First path received)
Extended Community: NT:192.168.1.3 NT:192.168.1.4
Last update: Tue Apr 11 23:19:33 2023
unet>
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Add an ability to match via route-maps. An additional route-map command
`match rpki-extcommunity <invalid|notfound|valid>` added.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
```
spine1-debian-11# sh ip bgp 100.100.100.101/32
BGP routing table entry for 100.100.100.101/32, version 21
Paths: (1 available, best #1, table default)
Not advertised to any peer
Local
fe80::ca5d:fd0d:cd8:1bb7 from eth3 (172.17.0.3)
(fe80::ca5d:fd0d:cd8:1bb7) (used)
Origin incomplete, metric 0, localpref 100, valid, internal, best (First path received)
Extended Community: OVS:invalid
Last update: Wed Aug 31 19:31:46 2022
spine1-debian-11# sh ip bgp 100.100.100.100/32
BGP routing table entry for 100.100.100.100/32, version 17
Paths: (1 available, best #1, table default)
Not advertised to any peer
Local
fe80::ca5d:fd0d:cd8:1bb7 from eth3 (172.17.0.3)
(fe80::ca5d:fd0d:cd8:1bb7) (used)
Origin incomplete, metric 0, localpref 100, valid, internal, best (First path received)
Extended Community: OVS:not-found
Last update: Wed Aug 31 19:31:46 2022
spine1-debian-11#
```
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
This is to avoid breaking changes between existing deployments of
extended community for bandwidth encoding. By default FRR uses uint32
to encode bandwidth, which is not as the draft requires (IEEE floating-point).
This switch enables the required encoding per-peer.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
https://datatracker.ietf.org/doc/html/draft-ietf-idr-link-bandwidth-07 says:
The bandwidth of the link is expressed as 4
octets in IEEE floating point format, units being bytes (not bits!)
per second. It is carried in the Local Administrator subfield of the
Value Field.
Before:
```
Extended Community (16), length: 8, Flags [OT]:
unknown extd community typecode (0x0004), Flags [none]
0x0000: 0004 fdeb 0001 e848
0x0000: 0004 fdeb 0001 e848
Updated routes:
172.16.16.1/32
```
0001 e848 - means 125000 (1Mbps), which is encoded incorrect.
After:
```
Extended Community (16), length: 8, Flags [OT]:
unknown extd community typecode (0x0004), Flags [none]
0x0000: 0004 fdeb 47f4 2400
0x0000: 0004 fdeb 47f4 2400
Updated routes:
172.16.16.1/32
```
47f4 2400 - means the same, but in floating point format.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
The `struct ecommunity` structure is using an int for a size value.
Let's switch it over to a uint32_t for size values since a size
value for data can never be negative.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
DF (Designated forwarder) election is used for picking a single
BUM-traffic forwarded per-ES. RFC7432 specifies a mechanism called
service carving for DF election. However that mechanism has many
disadvantages -
1. LBs poorly.
2. Doesn't allow for a controlled failover needed in upgrade
scenarios.
3. Not easy to hw accelerate.
To fix the poor performance of service carving alternate DF mechanisms
have been proposed via the following drafts -
draft-ietf-bess-evpn-df-election-framework
draft-ietf-bess-evpn-pref-df
This commit adds support for the pref-df election mechanism which
is used as the default. Other mechanisms including service-carving
may be added later.
In this mechanism one switch on an ES is elected as DF based on the
preference value; higher preference wins with IP address acting
as the tie-breaker (lower-IP wins if pref value is the same).
Sample output
=============
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
torm-11# sh bgp l2vpn evpn es 03:00:00:00:00:01:11:00:00:01
ESI: 03:00:00:00:00:01:11:00:00:01
Type: LR
RD: 27.0.0.15:6
Originator-IP: 27.0.0.15
Local ES DF preference: 100
VNI Count: 10
Remote VNI Count: 10
Inconsistent VNI VTEP Count: 0
Inconsistencies: -
VTEPs:
27.0.0.16 flags: EA df_alg: preference df_pref: 32767
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
torm-11# sh bgp l2vpn evpn route esi 03:00:00:00:00:01:11:00:00:01
*> [4]:[03:00:00:00:00:01:11:00:00:01]:[32]:[27.0.0.15]
27.0.0.15 32768 i
ET:8 ES-Import-Rt:00:00:00:00:01:11 DF: (alg: 2, pref: 100)
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
rfc 5701 is supported. it is possible to configure in bgp vpn, a list of
route target with ipv6 external communities to import. it is to be noted
that this ipv6 external community has been developed only for matching a
bgp flowspec update with same ipv6 ext commmunity.
adding to this, draft-ietf-idr-flow-spec-v6-09 is implemented regarding
the redirect ipv6 option.
Practically, under bgp vpn, under ipv6 unicast, it is possible to
configure : [no] rt6 redirect import <IPV6>:<AS> values.
An incoming bgp update with fs ipv6 and that option matching a bgp vrf,
will be imported in that bgp vrf.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
this commit supports [0] where ipv6 address is encoded in nexthop
attribute of nlri, and not in bgp redirect ip extended community. the
community contains only duplicate information or not.
Adding to this, because an action or a rule needs to apply to either
ipv4 or ipv6 flow, modify some internal structures so as to be aware of
which flow needs to be filtered. This work is needed when an ipv6
flowspec rule without ip addresses is mentioned, we need to know which
afi is served. Also, this work will be useful when doing redirect VRF.
[0] draft-simpson-idr-flowspec-redirect-02.txt
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
A new proxy flag has been added to the already existing NA extended
community to allow proxy advertisment of a local host by a VTEP that is
yet to indpendently establish local reachability.
Reference: draft-rbickhart-evpn-ip-mac-proxy-adv
The extendend mac-mobility sequence number needs to be synced across
the ES peers. However we cannot let a ES-peer path win over a local
path on the same ES. To accomplish that some parameters such as the
MM seq number are bubbled up from the non-best path to the local path.
This mechanism is explained further in the path-selection patch.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
1. EAD routes require support for ESI_LABEL extended community. The
primary info in this EC is a flags the specifies if the ES is
Single-active or active-acive.
2. Also fixed up ES_IMPORT_RT string. Support was added a long time
ago for ESR/Type-4 routes but it has not really been exercised for
MH functionality till now.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
When announcing ourselves as the next hop (e.g., to EBGP peers), if the
best path has the link bandwidth extended community and it is transitive,
change the value of the link bandwidth to the cumulative downstream
bandwidth (sum of the link bandwidths of all our multipaths) as this
makes the most sense. It is also implied by
https://tools.ietf.org/html/draft-mohanty-bess-ebgp-dmz. Of course, do
not override the link bandwidth if it has been specified by policy.
Note: Transitive extended communities will be automatically passed along
to EBGP peers; this commit is updating the value that is announced to
something that is the most appropriate.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Certain extended communities cannot be repeated. An example is the
BGP link bandwidth extended community. Enhance the extended community
add function to ensure uniqueness, if requested.
Note: This commit does not change the lack of uniqueness for any of
the already-supported extended communities. Many of them such as the
BGP route target can obviously be present multiple times. Others like
the Router's MAC should most probably be present only once. The portions
of the code which add these may already be structured such that duplicates
do not arise.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Additional extended community definitions and display of link-bandwidth
extended community.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Implement route-map option to set the link-bandwidth extended
community. The command is of the form:
set extcommunity bandwidth <(1-26214400)|cumulative|num-multipaths>
[non-transitive]
The options available are to specify the actual bandwidth value in
Mbps, base it on the cumulative downstream bandwidth or base it on
the number of multipaths. The last option is based on
https://tools.ietf.org/html/draft-mohanty-bess-ebgp-dmz. Further,
in alignment with the use case described in this IETF draft, the
extended community is encoded as transitive by default. There is an
option available to specify that it should be non-transitive.
The link-bandwidth itself is carried in bytes per second as specifed in
https://tools.ietf.org/html/draft-ietf-idr-link-bandwidth
Note: This commit only handles the processing for bandwidth specifed
as a value; subsequent commits will handle the processing of the other
options.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Some were converted to bool, where true/false status is needed.
Converted to void only those, where the return status was only false or true.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
During VRF-to-VRF route leaking, strip any extraneous route targets. This
ensures that source-VRF-specific route targets or route targets that are
internally assigned for the VRF-to-VRF route leaking don't get attached
to the route in the target VRF.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Tons of insane just-so pointer math here where it is not needed. This is
too smart. Use safer methods.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
While configuring aggregate route prepare the hash table first,
then prepare the aggregated ecomm value and then do the
unique sort once for ecommunity.
Signed-off-by: vishaldhingra<vdhingra@vmware.com>
It doesn't make much sense for a hash function to modify its argument,
so const the hash input.
BGP does it in a couple places, those cast away the const. Not great but
not any worse than it was.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
